The Tractive X-TREME fork cartridge kit for Ducati Multistrada V4 replaces the standard fork internals with a closed, pressurised cartridge system for more consistent damping control. The architecture keeps the damping oil under pressure to reduce aeration and maintain feel during sustained use. This kit also lowers the front ride height by 25mm, which can improve reach and confidence for some riders.

Design & features

  • Closed, pressurised cartridge design to help maintain damping consistency.
  • Fork-internal replacement kit aimed at improving control and comfort.
  • Built to be fully serviceable for long-term use.

Tuning Controls

This kit provides mechanical spring preload adjustment, allowing you to tailor sag and front-end attitude for rider weight and load.

Base Setup (factory preset)

A baseline setup is intended as a starting point after installation. Set rider sag first, then adjust preload as needed to balance comfort, steering response, and load support.

Before You Install

  • Plan for front-end height to be reduced by 25mm after fitment.
  • Confirm you have the tools and experience required for cartridge installation, or arrange professional fitment.
  • After installation, check sag and overall chassis balance before fine-tuning.

Serviceability/Lifecycle

The cartridge kit is fully serviceable to support periodic maintenance and rebuilds, helping keep performance consistent over time.

Is It Right For You?

This kit suits Multistrada V4 riders who want a lower front ride height and the ability to tune feel via preload adjustment, while benefiting from the consistency advantages of a closed, pressurised cartridge design.

Teknik Motorsport Pty Ltd Warranty terms for TracTive products.

This TracTive product has been assembled with the utmost care and tested according to ISO9001:2015 Quality system. In the unlikely event that the product does not fulfill your expectations because of faulty materials or manufacturing errors, please contact us through your dealer.

Teknik Motorsport Pty Ltd warrants that if, within 24 months of the date of sale the product is found to be defective as a result of manufacturing errors or faulty components, the product will be repaired free of charge by us, or by a TracTive approved repairer at our discretion.

Warranty covers the direct service material cost, service labour cost ($80/hr AUD) and shipping costs of the service partner. Other costs will be regarded on a case by case basis by Teknik Motorsport and TracTive.

 When a claim is made under the warranty, the following conditions have to be met:

  • You must have read the instructions carefully before mounting the product in the vehicle or adjusting the product.
  • The product has to be installed and adjusted as described in the instructions
  • The product must have been maintained and serviced in accordance with the recommendations in the manual. If not described in the manual, the recommended service intervals for regular street use: every 30.000 km or max 2 years, whichever is earlier.
  • Warranty shall apply only when TracTive original parts, procedures and tools have been used to service and/or repair, and if service and repair is performed by designated TracTive partners.
  • The product may not have been neglected, improperly used, altered or subjected to excessive loads. Excluded from warranty are normal wear, damage and rust.
  • A sales receipt or other proof of purchase originally eminating from Teknik Motorsport Pty Ltd. No warranty will be given on TracTive or Touratech products not purchased from or through Teknik Motorsport pty ltd.
  • Excluded from warranty are in particular products which are used in vehicles that are intended or suitable for taking part in sporting events, or have actually been used this way.
  • Recommended service interval for Motorsport applications: every season, or every 50 hours, every 10.000km or after any perceived loss in performance.
SKU 35DU21-D5310-TR
Model # 35DU21-D5310-TR
Barcode # 35DU21D5310TR
Brand TracTive Suspension
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.900m
Unit Of Measure Set
Type X-TREME
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front
Damping Adjustment Type Rebound & Compression
Seat Height Change (mm) Lowered -25
Shock Length Eye to Eye (mm) 805.0
Spring Rate Standard 6.4 N/mm
Type Code X-TREME
Stroke Metal to Metal (mm) 145
Notes Hydraulic end-stop
Fitted Spring 6.4-330

More From This Category