The Ohlins TTX Flow DV rear shock for Husqvarna FE 450, FE 501 and TE 300 is built around race-developed damping architecture for consistent control in off-road conditions. It uses a gas-pressurised, oil/gas separated design to help maintain damping stability as conditions change. This unit is supplied without a spring, allowing you to match spring rate to rider weight and intended use.

Ohlins | Made to race, perfected to ride

Ohlins off-road shocks are engineered to deliver controlled chassis behaviour and reliable damping feel across a wide range of trail and enduro inputs. The TTX Flow DV family focuses on maintaining composure and traction when the pace increases.

Shock design & features

  • TTX Flow DV shock architecture developed for enduro and off-road competition use
  • Gas-pressurised, oil/gas separated internal layout for damping consistency
  • Rear mono-shock configuration for the listed Husqvarna models

Tuning controls

  • Rebound damping adjustment to manage recovery and grip over repeated bumps
  • Compression damping adjustment to support the chassis under load and impacts
  • Spring preload is adjustable once a compatible spring is fitted (spring not supplied)

Before you install

  • No spring is supplied; select and fit the correct spring series noted for this shock
  • An optional preload adjuster is referenced for this model (see notes)
  • This part number is noted as replaced by DMX 1310

Serviceability/lifecycle

This is a rebuildable Ohlins unit designed for ongoing service. Regular inspection and oil service help keep damping performance consistent, particularly with enduro and competition-style use.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU DMX0310
Model # T46PR1C2W
Barcode # DMX0310
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.300 x 0.300 x 0.500m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear Mono
Shock Length Eye to Eye (mm) 457.0
Spring Rate No Spring/s Supplied
Type Code T46PR1C2W
Stroke Metal to Metal (mm) 137.0
Product Family TTX Flow DV
Notes 06310- spring series. Preload adjuster 15000-02 fits this shock. *Replaced by DMX 1310*
Fitted Spring Sold separately, see notes.
Rec. Ohlins Oil 01304-

More From This Category