The Ohlins FGK232 NIX 30 fork cartridge kit is built to improve control and feel at the front end of your Kawasaki Z 1000. It’s designed to deliver more consistent damping response through braking and corner entry. The focus is on clearer feedback and more confidence from the fork without changing the character of the bike.

Ohlins | Made to race, perfected to ride

Ohlins suspension components are developed with a strong emphasis on damping accuracy and repeatability. This cartridge kit is intended to give the fork a more composed, communicative response in real-world riding.

Shock design & features

  • Fork cartridge kit for the Kawasaki Z 1000
  • NIX 30 design from Ohlins
  • Improves front-end feedback and braking stability
  • Premium internal components for consistent performance and durability

Tuning controls

  • Separate compression and rebound adjustment to support finer tuning
  • Designed to be straightforward to set up for street use and occasional track riding

Is it right for you?

This kit suits riders chasing better mid-corner feel, improved control under braking, and a more planted front end. It’s a sensible choice if you want adjustability to match your riding style and conditions.

Before you install

Confirm compatibility with your exact model and year of Kawasaki Z 1000 before installation. Professional installation and setup is recommended to get the best result from the available adjustments.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGK232
Model # NIX 30
Barcode # FGK232
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate No Spring/s Supplied
Type Code NIX 30
Fork Length (mm) 727.0
Stroke Metal to Metal (mm) 120.0
Product Family NIX 30
Notes 08790-xx series spring
Fitted Spring Sold separately, see notes.

More From This Category