The Ohlins FGR162 complete front fork assembly is designed to improve front-end control and stability on the BMW HP 4 and S 1000 RR. It focuses on delivering clear feel under braking and through mid-corner loading, helping the rider read grip and chassis balance. Built as a full front fork unit, it’s intended for riders who want a more communicative and consistent suspension response.

Ohlins | Made to race, perfected to ride

Ohlins race-derived suspension is built around predictable damping behaviour and repeatable adjustment. The FGR162 follows that approach with an emphasis on stability, confidence, and clear feedback at the front tyre.

Who this fork is for

  • BMW HP 4 and S 1000 RR owners chasing improved front-end feel
  • Riders who want stronger braking stability and calmer chassis behaviour
  • Street-focused riders who also do occasional track use

Fork design & features

  • Complete front fork unit (FGR162 / FGR 100)
  • Premium internal components aimed at consistent performance and durability
  • Refined damping characteristics to support stability and mid-corner confidence

Tuning controls

  • Separate compression adjustment
  • Separate rebound adjustment
  • Designed for straightforward setup changes between road and track-oriented riding

Is it right for you?

If your priority is a more informative front end with improved control under braking and better mid-corner support, the FGR162 is a strong match. If you’re looking for a minor change only, or don’t intend to adjust damping, a simpler fork upgrade path may suit better.

Before you install

  • Confirm model compatibility: BMW HP 4 and BMW S 1000 RR
  • Plan an initial setup and safety check after installation before pushing pace
  • Use a workshop familiar with performance suspension for best results

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGR162
Model # TTX25G
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate Standard 9.5 / 10.0 / 10.5 N/mm
Type Code TTX25G
Fork Length (mm) 741.0
Stroke Metal to Metal (mm) 120.0
Product Family FGR 100
Notes *Replaced by FKR 104* Springs -95,-10,-05 included in kit, Race use only. Only to be used with Öhlins Shock Absorber on DDC equipped bikes
Fitted Spring 04744-95/-10/-05

More From This Category