The Ohlins FGK126 NIX 30 front fork cartridge is designed to improve front-end performance and rider confidence on the Honda CBR1000RR. It focuses on refined damping behaviour for better braking stability and clearer feedback through the bars. The result is a more composed, communicative front end for road riding and track use.

Ohlins | Made to race, perfected to ride

Built around Ohlins cartridge technology, this kit targets control and consistency at the front wheel so you can ride with more precision in changing conditions.

Who this cartridge kit is for

  • CBR1000RR riders wanting a more stable, confidence-inspiring front end under brakes
  • Riders chasing improved mid-corner feel and steering accuracy
  • Spirited street riders and those doing occasional track days

Shock design & features

  • NIX 30 fork cartridge kit for the front fork
  • Refined damping characteristics aimed at composure and feedback
  • Premium internal components for consistent performance

Tuning controls

  • Separate compression and rebound adjustment to fine-tune suspension response

Before you install

  • Confirm fitment for your specific Honda CBR1000RR model/year before installation
  • Installation and setup are best handled by a qualified suspension technician

Need help choosing?

If you want a front end with better braking stability and clearer feedback without turning the bike into a dedicated race-only setup, this Ohlins cartridge kit is a strong match for mixed road and track riding.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGK126
Model # NIX 30
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate Standard 9.0 N/mm
Type Code NIX 30
Product Family NIX 30
Fitted Spring 04744-90

More From This Category