The Ohlins FGR160 FGR 100 complete front fork is designed to improve front-end control and feel on the Ducati 1098, 1198 and 848. It focuses on delivering stable braking behaviour and clearer feedback through the turn. With external adjustability, it supports a tailored setup for spirited road use and track riding.

Ohlins | Made to race, perfected to ride

Developed with a performance-first approach, this complete fork assembly targets consistent damping behaviour and predictable chassis response. It is intended as a front suspension upgrade where rider feel and control are the priority.

Who this fork is for

  • Ducati 1098, 1198 and 848 riders chasing improved front-end feedback
  • Road riders wanting better stability under braking
  • Track day riders looking for a more tuneable front end

Fork design & features

  • Complete front fork unit
  • Premium internal components for consistent performance and durability
  • Improved braking stability and mid-corner feel focus

Tuning controls

  • Separate compression adjustment
  • Separate rebound adjustment

Before you install

  • Confirm compatibility with your Ducati 1098, 1198 or 848 variant before fitting
  • After installation, set sag and damping adjustments methodically to suit tyres and riding conditions

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGR160
Model # TTX25G
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions

If your Motorcycle is listed below, this product will suit:

Position (Front or Rear) Front cartridge
Spring Rate Standard 9.0 / 9.5 / 10.0 N/mm
Type Code TTX25G
Fork Length (mm) 717.0
Stroke Metal to Metal (mm) 120.0
Product Family FGR 100
Notes Springs -90,-95,-10 included in kit
Fitted Spring 04744-90/-95/-10

More From This Category