The Ohlins FGR179 complete front fork assembly is designed to deliver refined front-end control for Ducati 899 Panigale and 959 Panigale models. It focuses on improving stability under braking and maintaining clear feedback through the corner. Separate damping adjusters allow you to tailor the feel to your riding and conditions.

Ohlins | Made to race, perfected to ride

Built as a complete front fork unit, the FGR179 is aimed at riders chasing a more composed and communicative front end. It is suited to spirited road use and occasional track riding where consistent feel matters.

Who this fork is for

  • Ducati 899 Panigale and 959 Panigale riders wanting improved braking stability and mid-corner support
  • Riders who value front-end feedback and a controlled chassis attitude
  • Owners looking for a complete Ohlins front fork solution

Fork design & features

  • Complete front fork assembly
  • Designed to enhance front-end feedback and braking stability
  • Premium internal components for consistent suspension response and durability

Tuning controls

  • Separate compression damping adjustment
  • Separate rebound damping adjustment

Is it right for you?

If you want more confidence on the brakes and a calmer, more informative front end through turns, this fork aligns well with that goal. If you prefer a fit-and-forget setup with no interest in tuning, adjustable damping may be more than you need.

Before you install

  • Confirm compatibility with your Ducati 899 Panigale or 959 Panigale model and existing front-end components
  • Plan a baseline setup after installation so adjustments start from a known point

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGR179
Model # TTX25G
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate Standard 9.5 / 10.0 / 10.5 N/mm
Type Code TTX25G
Fork Length (mm) 738.0
Stroke Metal to Metal (mm) 120.0
Product Family FGR 100
Notes *Replaced by FKR 115* Showa fork, Springs -95,-10,-05 included in kit
Fitted Spring 04744-95/-10/-05

More From This Category