The Ohlins HA1882 TTX Flow rear shock is built for Husqvarna TX 125, TE 250 and FE 250 riders who want consistent damping control and clear chassis feedback in MX and enduro conditions. Developed from Ohlins racing architecture, it is designed to maintain stability as pace and terrain intensity increase. This is a gas-pressurised, oil/gas separated shock to help keep damping consistent through longer rides.

Ohlins | Made to race, perfected to ride

TTX Flow technology focuses on predictable damping response and traction, with a design aimed at reducing fade and keeping the rear tyre working under load. It is suited to riders who tune suspension for changing tracks, traction levels and rider preference.

Who this shock is for

  • Husqvarna TX 125, TE 250 and FE 250 owners upgrading rear suspension control
  • Riders chasing more consistent feel across motos, stages or long sessions
  • Those who want adjustment range for different terrain and riding intensity

Shock design & features

  • TTX Flow rear mono shock layout
  • Gas-pressurised damping with oil/gas separation to support stable damping behaviour
  • Independent damping circuits designed for controlled response and traction

Tuning controls

  • Compression damping adjustment
  • Rebound damping adjustment

Before you install

  • No spring is supplied; spring is sold separately (see product notes for spring series guidance)
  • Fitment note: this shock can be modified to suit a 2020 year-model bike with changes to shimming and length according to the spec card

Serviceability/lifecycle

As with all performance off-road shocks, routine servicing helps maintain damping consistency and seal life. Service intervals should be based on riding conditions, hours and contamination exposure.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU HA1882
Model # T46PR1C1W
Barcode # HA1882
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.300 x 0.300 x 0.500m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear Mono
Shock Length Eye to Eye (mm) 478.0
Spring Rate No Spring/s Supplied
Type Code T46PR1C1W
Product Family TTX Flow
Notes 06310- series spring. HA 1882 can be modified to fit year model 2020 bike with change of shimming and lenght according to spec card.
Fitted Spring Sold separately, see notes.

More From This Category