The Ohlins HO360 TTX GP rear shock is built for riders chasing precise damping control and stable chassis behaviour on the Honda CBR1000RR. Developed from Ohlins racing know-how, it is designed to deliver clear feel at the tyre and consistent response through repeated hard use. This is a gas-pressurised, oil/gas separated rear mono shock for focused track and performance road riding.

Ohlins | Made to race, perfected to ride

TTX GP is Ohlins’ high-performance rear shock platform aimed at riders who want accurate feedback and repeatable damping control. The design prioritises stability on the brakes and traction on corner exit, with adjustability suited to dialling the bike in for different conditions.

Shock design & features

  • Rear mono shock architecture for the CBR1000RR fitment
  • Gas-pressurised, oil/gas separated design to help maintain consistent damping behaviour during extended sessions
  • TTX GP damping concept developed from circuit use, focused on control and feel

Tuning controls

This shock provides external adjustment for rebound damping and compression damping. These controls let you balance support and grip to suit your pace, tyres and track surface, while keeping the bike composed under braking and during direction changes.

Is it right for you?

Choose this unit if you want a dedicated performance rear shock with race-derived damping character and the ability to fine-tune compression and rebound. It suits riders who are actively setting up their suspension rather than simply replacing worn components.

Before you install

Confirm compatibility for your exact CBR1000RR model and year, and plan to set sag and baseline damping after installation. Notes in the product data indicate this model has been replaced by HO 466, which may matter for availability and future parts planning.

Serviceability/lifecycle

As a serviceable Ohlins shock, periodic maintenance helps keep damping performance consistent over time. Service intervals depend on use (especially track time), cleanliness and operating conditions.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU HO360
Model # T36PR1C1LS
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.300 x 0.300 x 0.500m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear Mono
Shock Length Eye to Eye (mm) 302.0 +4/-2
Spring Rate Standard 105.0 N/mm
Type Code T36PR1C1LS
Stroke Metal to Metal (mm) 60.0
Product Family TTX GP
Notes *Replaced by HO 466*
Fitted Spring 21040-36
Spring Colour Yellow

More From This Category