The Ohlins DMX0306 rear shock is built for Sherco enduro and MX applications where consistent damping control and clear feedback matter. Based on Ohlins TTX Flow DV architecture, it uses a gas-pressurised design to help maintain damping stability through longer, harder sessions. Supplied without a spring, it is intended to be paired with the correct spring series noted for this model.

Ohlins | Made to race, perfected to ride

Ohlins suspension is developed with a focus on controlled damping behaviour and repeatability in demanding conditions. The TTX Flow DV family is aimed at riders who want a planted feel and predictable chassis response across changing terrain and pace.

Shock design & features

This is a gas-pressurised, oil/gas separated rear mono shock using the Ohlins TTX Flow DV layout. The design is intended to support stable damping characteristics and consistent handling feel as conditions and loads change.

Tuning controls

The shock provides external adjustment for rebound damping and compression damping, allowing you to tailor behaviour for traction, stability and rider preference. It also supports preload adjustment via an optional preload adjuster (as noted for this shock).

Base setup (factory preset)

Ohlins supplies the unit with a baseline setting intended as a starting point for the listed Sherco models. Final setup should be confirmed once the correct spring is selected and installed, then adjusted to suit rider weight, terrain and pace.

Before you install

  • No spring is supplied; select the appropriate spring series referenced in the notes for this model.
  • Confirm fitment to your exact Sherco variant before installation.
  • Use the recommended Ohlins shock oil specified for this unit.

Serviceability/lifecycle

As with any high-performance shock, periodic servicing helps maintain damping consistency and seal life. Regular inspection and scheduled oil and seal service are recommended, especially with frequent off-road use.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU DMX0306
Model # T46PR1C2W
Barcode # DMX0306
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.300 x 0.300 x 0.500m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear Mono
Shock Length Eye to Eye (mm) 480.0
Spring Rate No Spring/s Supplied
Type Code T46PR1C2W
Stroke Metal to Metal (mm) 137.0
Product Family TTX Flow DV
Notes 06310- & 06451- spring series. Preload adjuster 15000-02 fits this shock.
Fitted Spring Sold separately. See notes.
Rec. Ohlins Oil 01304-

More From This Category