The Ohlins FGK202 NIX 30 fork cartridge kit is a front suspension upgrade designed for the Yamaha YZF R6. It focuses on improving front-end control and feel under braking and through corners. Built around Ohlins cartridge technology, it provides a more consistent damping response and clearer feedback to the rider.

Ohlins | Made to race, perfected to ride

Ohlins fork cartridge kits are developed to increase stability, confidence and consistency at the front tyre. The FGK202 is intended to deliver a composed, communicative front end without compromising adjustability for different conditions.

Who this kit is for

  • YZF R6 riders looking for improved front-end feedback and stability
  • Spirited street riders who want more control and consistency
  • Track day riders seeking a more tunable front suspension feel

Shock design & features

  • NIX 30 fork cartridge design
  • Premium internal components aimed at consistent damping performance
  • Improved braking stability and mid-corner feel compared with a basic setup

Tuning controls

  • Separate compression adjustment
  • Separate rebound adjustment

Before you install

  • Confirm compatibility with your exact Yamaha YZF R6 model and year before fitting
  • Installation and setup are best handled by a suspension technician to suit rider weight and intended use

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGK202
Model # NIX 30
Barcode # FGK202
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate No Spring/s Supplied
Type Code NIX 30
Fork Length (mm) 744.0
Stroke Metal to Metal (mm) 120.0
Product Family NIX 30
Notes 08790-xx series spring
Fitted Spring Sold separately. See notes.

More From This Category