The Ohlins TTX Flow rear shock is built for Beta RR enduro riders who want consistent damping behaviour and clear tuning pathways across changing terrain. It uses an oil/gas separated design to help manage heat and keep response predictable over longer rides. Spring selection is separate, allowing you to match the shock to rider weight and intended use.

Ohlins | Made to race, perfected to ride

TTX Flow technology is developed from competition-focused suspension architecture, with an emphasis on stable damping and controllable chassis behaviour. This unit is intended as a complete rear shock replacement for the listed Beta RR models.

Who this shock is for

Suited to riders who want improved control and traction feel in enduro conditions, including those tuning for different tracks, tyres, or riding pace. It is also a practical choice if you want a higher-quality serviceable rear shock platform with external adjustments.

Shock design & features

This is a gas-pressurised, oil/gas separated rear mono shock. The TTX Flow layout is designed to keep damping performance consistent and to provide a broad, usable adjustment range when setting the bike up for varying surfaces.

Tuning controls

External damping adjustments are provided for compression and rebound. These controls let you balance support and comfort, and fine-tune how the rear tracks under acceleration, braking, and repeated impacts.

Before you install

No spring is supplied. This shock uses the 06310- and 06451- spring series; choose and fit a suitable spring before installation. Use Ohlins oil 01304- when servicing as required.

Serviceability/lifecycle

As a serviceable performance shock, periodic maintenance helps maintain damping consistency and seal life, particularly in muddy or high-hour enduro use. Plan service intervals based on ride hours and conditions.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU BA2084
Model # T46PR1C1W
Barcode # BA2084
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.300 x 0.300 x 0.500m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear Mono
Spring Rate No Spring/s Supplied
Type Code T46PR1C1W
Product Family TTX Flow
Notes 06310- & 06451- spring series
Fitted Spring Sold separately, see notes.
Rec. Ohlins Oil 01304-

More From This Category