The Ohlins FGK218 NIX 30 fork cartridge kit is designed to improve control and feel at the front end of the Yamaha FZ 8. It focuses on delivering more consistent damping behaviour and clearer feedback under braking and through corners. Separate adjustment circuits allow more accurate tuning to suit your riding and conditions.

Ohlins | Made to race, perfected to ride

Ohlins cartridge kits are built around proven damping design to help the fork respond more predictably across changing loads and road surfaces. The goal is improved confidence from the front tyre without compromising day-to-day usability.

Who this kit is for

  • Yamaha FZ 8 riders wanting improved front-end feedback and stability
  • Street riders who value stronger braking support and mid-corner control
  • Riders who want tuning capability for occasional track use

Shock design & features

  • NIX 30 fork cartridge design
  • Premium internal components for consistent damping performance
  • Improves handling precision and stability by refining fork damping characteristics

Tuning controls

  • Separate compression and rebound damping adjustments
  • Supports fine-tuning for road riding and occasional track conditions

Before you install

  • Confirm compatibility with Yamaha FZ 8 and the FGK218 kit before fitting
  • Installation and setup should be completed by a qualified suspension technician to ensure correct operation and adjustment access

Serviceability/lifecycle

As a cartridge-based upgrade, the kit is intended to be maintained like other performance suspension components. Routine servicing helps keep damping consistent and preserves ride quality over time.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGK218
Model # NIX 30
Barcode # FGK218
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate No Spring/s Supplied
Type Code NIX 30
Fork Length (mm) 745.0
Stroke Metal to Metal (mm) 130.0
Product Family NIX 30
Notes 08790-xx series spring
Fitted Spring Sold separately, see notes.

Related products

More From This Category