The Ohlins FGR176 FGR 100 Complete Front Fork is built to deliver a controlled, communicative front end for the Honda CBR600RR. It focuses on consistent damping behaviour to improve stability under braking and feel through mid-corner. Designed for riders who want a more precise and confidence-inspiring front suspension response.

Ohlins | Made to race, perfected to ride

Developed from Ohlins racing experience, the FGR platform is intended to provide predictable support and clear feedback at the front tyre. The goal is a composed chassis that lets you focus on lines and braking points rather than chasing inconsistent feel.

Who this fork is for

  • Honda CBR600RR riders seeking better front-end feedback and stability
  • Street riders who prioritise control and confidence
  • Track-day riders wanting a front end that stays composed as pace increases

Fork design & features

  • Complete front fork assembly designed for the Honda CBR600RR
  • Refined damping system aimed at improved braking stability and mid-corner feel
  • Premium internal components for consistent performance

Tuning controls

  • Separate compression adjustment
  • Separate rebound adjustment
  • Designed to be straightforward to set up for road use and occasional track riding

Before you install

  • Confirm compatibility with your exact CBR600RR year/model and front-end configuration before fitting
  • After installation, allow time to baseline your settings and verify steering, brake and guard clearances

Need help choosing?

If you are comparing options for your CBR600RR or want guidance on a sensible starting point for road and track use, contact Teknik Motorsport with your bike details and current suspension setup.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGR176
Model # TTX25G
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Type Code TTX25G
Fork Length (mm) 717.0
Stroke Metal to Metal (mm) 120.0
Product Family FGR 100
Notes *Replaced by FKR 110* Showa, Springs -90,-95,-10 included in kit.
Fitted Spring 04744-90/-95/-10

More From This Category