The Tractive X-CITE shock for the Triumph Tiger 900 Rally (Pro) is a closed, pressurised shock absorber built around a separated oil and gas design for consistent damping over varied conditions. It uses an internal separation piston to keep the damping oil stable and reduce fade during sustained use. This model is configured with rebound adjustment to help fine-tune ride control to your load and riding style.

Design & features

  • Closed, pressurised shock design to support consistent damping
  • Oil/gas separation via an internal separation piston (not an emulsion layout)
  • Tractive X-CITE architecture intended for controlled, predictable response across changing surfaces

Tuning Controls

  • Rebound damping adjustment

Base Setup (factory preset)

This shock is supplied with a baseline internal setup from Tractive. Fine-tuning is typically done via the rebound adjuster after installation to suit rider preference and real-world loading.

Before You Install

  • Confirm model and fitment for your Tiger 900 Rally (Pro) before installation
  • Check for correct clearances and routing around the shock body during refit
  • After installation, verify sag and then fine-tune rebound to match your use

Serviceability/Lifecycle

As a pressurised, oil/gas-separated shock, periodic servicing helps maintain damping consistency and seal performance over time. Service intervals and parts requirements depend on use conditions and mileage.

Is It Right For You?

This configuration suits riders who want a quality pressurised shock with the ability to tune rebound for different loads and riding conditions, while keeping the control set straightforward.

Teknik Motorsport Pty Ltd Warranty terms for TracTive products.

This TracTive product has been assembled with the utmost care and tested according to ISO9001:2015 Quality system. In the unlikely event that the product does not fulfill your expectations because of faulty materials or manufacturing errors, please contact us through your dealer.

Teknik Motorsport Pty Ltd warrants that if, within 24 months of the date of sale the product is found to be defective as a result of manufacturing errors or faulty components, the product will be repaired free of charge by us, or by a TracTive approved repairer at our discretion.

Warranty covers the direct service material cost, service labour cost ($80/hr AUD) and shipping costs of the service partner. Other costs will be regarded on a case by case basis by Teknik Motorsport and TracTive.

 When a claim is made under the warranty, the following conditions have to be met:

  • You must have read the instructions carefully before mounting the product in the vehicle or adjusting the product.
  • The product has to be installed and adjusted as described in the instructions
  • The product must have been maintained and serviced in accordance with the recommendations in the manual. If not described in the manual, the recommended service intervals for regular street use: every 30.000 km or max 2 years, whichever is earlier.
  • Warranty shall apply only when TracTive original parts, procedures and tools have been used to service and/or repair, and if service and repair is performed by designated TracTive partners.
  • The product may not have been neglected, improperly used, altered or subjected to excessive loads. Excluded from warranty are normal wear, damage and rust.
  • A sales receipt or other proof of purchase originally eminating from Teknik Motorsport Pty Ltd. No warranty will be given on TracTive or Touratech products not purchased from or through Teknik Motorsport pty ltd.
  • Excluded from warranty are in particular products which are used in vehicles that are intended or suitable for taking part in sporting events, or have actually been used this way.
  • Recommended service interval for Motorsport applications: every season, or every 50 hours, every 10.000km or after any perceived loss in performance.
SKU 46TR20-R3315-TR
Model # 46TR20-R3315-TR
Barcode # 46TR20R3315TR
Brand TracTive Suspension
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.400m
Unit Of Measure ea
Type X-CITE
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear
Damping Adjustment Type Rebound
Shock Options - Hydraulic Preload Adjuster Hydraulic with knob
Seat Height Change (mm) Lowered -20
Shock Length Eye to Eye (mm) 403.0
Spring Rate Standard 140 N/mm
Type Code X-CITE
Stroke Metal to Metal (mm) 89.6
Fitted Spring 140-205

You May Also Like

More From This Category