The Tractive X-CITE shock for the Yamaha Tenere 700 uses a closed, pressurised monotube design with an internal separation piston to keep damping consistent and reduce cavitation under sustained use. It is built as a complete rear shock assembly with a spring fitted. This model provides rebound damping adjustment for tailored control across mixed road and off-road conditions.

Design & features

  • Closed, pressurised monotube construction
  • Internal oil/gas separation via piston (not an emulsion design)
  • Supplied as a sprung shock assembly

Tuning Controls

  • Rebound damping adjustment

Base Setup (factory preset)

The shock is supplied with a factory baseline tune intended to suit general riding. Fine-tuning is done via the rebound adjuster to match load, tyres, terrain, and riding pace.

Before You Install

  • Confirm model fitment for your Yamaha Tenere 700 and year range before installation
  • Set sag with the correct spring preload for your rider weight and typical luggage
  • After installation, re-check fasteners and clearances through full suspension travel

Serviceability/Lifecycle

As a pressurised shock with separated oil and gas, it is designed to be serviced to restore performance over time. Service intervals depend on use conditions, especially dirt and high-heat riding.

Teknik Motorsport Pty Ltd Warranty terms for TracTive products.

This TracTive product has been assembled with the utmost care and tested according to ISO9001:2015 Quality system. In the unlikely event that the product does not fulfill your expectations because of faulty materials or manufacturing errors, please contact us through your dealer.

Teknik Motorsport Pty Ltd warrants that if, within 24 months of the date of sale the product is found to be defective as a result of manufacturing errors or faulty components, the product will be repaired free of charge by us, or by a TracTive approved repairer at our discretion.

Warranty covers the direct service material cost, service labour cost ($80/hr AUD) and shipping costs of the service partner. Other costs will be regarded on a case by case basis by Teknik Motorsport and TracTive.

 When a claim is made under the warranty, the following conditions have to be met:

  • You must have read the instructions carefully before mounting the product in the vehicle or adjusting the product.
  • The product has to be installed and adjusted as described in the instructions
  • The product must have been maintained and serviced in accordance with the recommendations in the manual. If not described in the manual, the recommended service intervals for regular street use: every 30.000 km or max 2 years, whichever is earlier.
  • Warranty shall apply only when TracTive original parts, procedures and tools have been used to service and/or repair, and if service and repair is performed by designated TracTive partners.
  • The product may not have been neglected, improperly used, altered or subjected to excessive loads. Excluded from warranty are normal wear, damage and rust.
  • A sales receipt or other proof of purchase originally eminating from Teknik Motorsport Pty Ltd. No warranty will be given on TracTive or Touratech products not purchased from or through Teknik Motorsport pty ltd.
  • Excluded from warranty are in particular products which are used in vehicles that are intended or suitable for taking part in sporting events, or have actually been used this way.
  • Recommended service interval for Motorsport applications: every season, or every 50 hours, every 10.000km or after any perceived loss in performance.
SKU 46YA19-R2313-TR
Model # 46YA19-R2313-TR
Barcode # 46YA19R2313TR
Brand TracTive Suspension
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.400m
Unit Of Measure ea
Type X-CITE
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear
Damping Adjustment Type Rebound
Shock Options - Hydraulic Preload Adjuster Hydraulic with knob
Seat Height Change (mm) Standard Height
Shock Length Eye to Eye (mm) 371.0
Spring Rate Standard 90 N/mm
Type Code X-CITE
Stroke Metal to Metal (mm) 97.0
Notes PDSII anti-bottoming
Fitted Spring 90-235

You May Also Like

Related products

More From This Category