The Ohlins DMX1309 is a rear TTX Flow DV shock absorber for Husqvarna FE 250, FE 350, TE 150 and TE 250 models. Built around Ohlins’ twin-tube TTX architecture, it is designed to deliver consistent damping behaviour and clear feedback across changing conditions. This unit uses a gas-pressurised, oil/gas separated damping system for stability during sustained use.

Ohlins | Made to race, perfected to ride

TTX Flow DV shocks are developed from Ohlins racing suspension programs and adapted for enduro and off-road use. The focus is predictable chassis support, traction and control, with damping circuits designed to remain consistent over long, demanding stages.

Who this shock is for

  • Riders looking for improved control and feel from the rear of the bike in enduro or off-road conditions
  • Owners who want broader, more precise adjustability to suit different terrain and pace
  • Anyone refreshing a worn rear shock and aiming for a higher level of damping consistency

Shock design & features

  • TTX twin-tube damping layout (TTX Flow DV product family)
  • Gas-pressurised, oil/gas separated design to help maintain stable damping performance
  • Rear mono-shock fitment for the listed Husqvarna FE/TE models

Tuning controls

This shock includes external rebound and compression damping adjustments, allowing you to tailor response for traction, braking stability and terrain changes. The separated damping circuits support more precise tuning compared with simpler shock architectures.

Before you install

  • Spring is sold separately; confirm the correct spring series noted for this shock before ordering
  • Ohlins notes indicate it replaces DMX 0309; verify suitability against your bike and existing setup
  • Use the recommended Ohlins shock oil specified for the unit during service

Serviceability / lifecycle

Like all performance off-road shocks, regular servicing helps maintain damping consistency and seal life. Ohlins components are designed to be serviced and re-valved, supporting long-term ownership and setup changes over time.

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU DMX1309
Model # T46PR1C2W
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.300 x 0.300 x 0.500m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Rear Mono
Shock Length Eye to Eye (mm) 457.0
Type Code T46PR1C2W
Stroke Metal to Metal (mm) 137.0
Product Family TTX Flow DV
Notes 06310- spring series. Preload adjuster 15000-02 fits this shock. *Replaces DMX 0309*
Fitted Spring Sold separately, see notes.
Rec. Ohlins Oil 01304-

More From This Category