The Ohlins FGK240 NIX 30 fork cartridge kit is designed to improve front-end control and feel on the BMW M 1000 RR and S 1000 RR. It focuses on delivering consistent damping behaviour for better composure under braking and clearer feedback through the corner. Adjustment is provided to help tailor the fork response to rider preference and conditions.

Ohlins | Made to race, perfected to ride

Ohlins cartridge kits are built to bring race-proven damping concepts to high-performance road and track motorcycles. The FGK240 is aimed at riders looking for more confidence from the front tyre without compromising tuneability.

Who this kit is for

  • BMW M 1000 RR and S 1000 RR riders wanting improved braking stability and front-end feedback
  • Spirited street riding with occasional track use
  • Riders who value precise suspension tuning rather than a one-size setting

Shock design & features

  • NIX 30 fork cartridge design
  • Premium internal components for consistent damping performance
  • Improves mid-corner feel and front-end composure

Tuning controls

  • Separate compression and rebound adjustment for targeted setup changes

Before you install

  • Confirm model compatibility for your BMW M 1000 RR or S 1000 RR variant before fitting
  • Installation and setup should be carried out by a qualified suspension technician to ensure correct function and adjustment range

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGK240
Model # NIX 30
Barcode # FGK240
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate No Spring/s Supplied
Type Code NIX 30
Fork Length (mm) 756.0
Stroke Metal to Metal (mm) 120.0
Product Family NIX 30
Notes 08790-xx series spring, This product should not be used with the BMW DDC system. This product should only be used with non-electronic units.
Fitted Spring Sold separately. See notes.

You May Also Like

More From This Category