The Ohlins FGR161 NIX 30 fork cartridge kit is designed to improve front-end control and feel on KTM RC8 and RC8R models. It focuses on delivering consistent damping behaviour for better feedback under brakes and through mid-corner. Adjustment is straightforward, making it suitable for riders who want a more composed and communicative front end on road and occasional track days.

Ohlins | Made to race, perfected to ride

Built around Ohlins cartridge technology, the FGR161 aims to provide predictable support and clearer tyre contact feel. It is intended as a performance-focused internal upgrade to the front fork, centred on damping quality and tunability rather than cosmetic changes.

Who this cartridge kit is for

  • Riders chasing improved braking stability and front-end feedback
  • KTM RC8/RC8R owners wanting more precise fork control for spirited road riding
  • Track-day riders looking for easier tuning and consistent feel

Shock design & features

  • NIX 30 fork cartridge product family
  • Premium internal components for consistent damping performance
  • Designed to enhance mid-corner feel and overall front-end composure

Tuning controls

  • Separate compression and rebound adjustment to tailor fork response
  • Simple setup approach suited to both road and track conditions

Before you install

  • Mounting position: front
  • Stroke: 125 mm
  • Springs included in kit: Springs -95, -10, -05

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGR161
Model # NIX 30
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Type Code NIX 30
Stroke Metal to Metal (mm) 125.0
Product Family NIX 30
Notes TTX25 Cartridge kit
Fitted Spring Springs -95 -10 -05 included in kit

More From This Category