The Ohlins FGR174 FGR 100 complete front fork is designed for Ducati 1199 and 1299 Panigale models fitted with Marzocchi forks. It focuses on improving front-end control with a more composed feel under braking and through mid-corner loads. Separate damping adjustments help you tailor the response to your riding and conditions.

Ohlins | Made to race, perfected to ride

Built as a complete front fork assembly, the FGR 100 platform is intended to deliver consistent damping behaviour and clear rider feedback. Premium internal components support reliable performance across road and track-focused use.

Who this fork is for

  • Ducati 1199 Panigale riders with Marzocchi forks looking for improved braking stability and front-end feel
  • Ducati 1299 Panigale riders with Marzocchi forks wanting more control for spirited street riding and occasional track use

Shock design & features

  • Complete front fork assembly (FGR 100)
  • Improves front-end feedback and braking stability for better control
  • Premium internal components for consistent, reliable performance

Tuning controls

  • Separate compression adjustment
  • Separate rebound adjustment

Is it right for you?

Choose the FGR174 if your Ducati 1199 or 1299 Panigale is equipped with Marzocchi forks and you want a more communicative front end with adjustability for your preferred feel. If your bike uses a different fork type, confirm fitment before ordering.

Before you install

  • Confirm your motorcycle is a Ducati 1199 or 1299 Panigale with Marzocchi forks
  • Plan your initial adjustments based on your current setup and intended use (road or track)

Öhlins Motorcycle Suspension Warranty

New Öhlins motorcycle shock absorbers, front forks and cartridge kits supplied by Teknik Motorsport are covered by the applicable Öhlins manufacturer’s warranty against defects in materials and workmanship.

Teknik Motorsport is an authorised Öhlins Service Centre and administers warranty claims in accordance with the Öhlins warranty conditions. The service intervals below form part of the maintenance requirements for Öhlins products supplied and supported by Teknik Motorsport.

This warranty is in addition to the consumer guarantees that apply under the Australian Consumer Law.

  • Registered motorcycles — non-competition road use Five years, subject to correct application, installation, setup and servicing every: 20,000 km or two years, whichever occurs first.
  • Registered motorcycles — adventure and light off-road use Five years, subject to correct application, spring rate, setup and servicing every: 10,000 km or annually, whichever occurs first.
  • Unregistered or competition motorcycles Two years for eligible Öhlins MX and Enduro products, subject to inspection every ten hours and servicing every: 30 operating hours or annually, whichever occurs first.

Compliance with the applicable service interval is a condition of the Öhlins manufacturer’s warranty. Evidence of servicing may be required when a warranty claim is assessed.

A seal leak, loss of damping performance or internal wear arising after the prescribed service interval has been exceeded will be treated as a service or maintenance issue rather than a manufacturing defect.

Warranty repairs

Öhlins suspension products are designed to be serviced and repaired. Where a warranty claim is approved, the normal remedy is repair of the customer’s original suspension unit using genuine Öhlins replacement parts.

Replacement of a complete shock absorber, fork or cartridge kit is not automatic and would normally occur only where the product has suffered a manufacturing failure that cannot reasonably be repaired. This is at Ohlins discretion. 

Öhlins spare parts and service kits

Öhlins spare parts, seals, bushes, service kits, springs, fluids and individual components are covered only against defects present when supplied.

No fixed age-based warranty applies to wear items, service parts or consumable components. Wear, deterioration, contamination, incorrect installation and damage caused by another component are not manufacturing defects.

Öhlins gives the customer a meaningful five-year warranty on products (Units), provided the suspension is maintained as suspension should be maintained. Teknik supports that warranty locally, can inspect the product properly, and can repair it with genuine parts rather than discarding it.

SKU FGR174
Model # TTX25G
Brand Ohlins
Shipping Weight 5.0000kg
Shipping Size 0.200 x 0.200 x 0.800m
Type Units
See our Shipping Information See our Frequently Asked Questions
Position (Front or Rear) Front cartridge
Spring Rate Standard 9.5 / 10.0 / 10.5 N/mm
Type Code TTX25G
Fork Length (mm) 741.0
Stroke Metal to Metal (mm) 120.0
Product Family FGR 100
Notes Springs -95,-10,-05 included in kit
Fitted Spring 04744-95/-10/-05

More From This Category